Appliance repair referrals for Denver & nearby townsCall: (720) 679-7046
(720) 679-7046

Water Hardness and Your Appliances in the Denver Area

appliancerepairdenverco.net

Hardness is the amount of dissolved calcium and magnesium in your tap water, and in the Denver metro it ranges from soft to very hard depending on which utility sends water to your house. That one number explains a lot of the scale, clogged lines and short-lived heating parts that repair companies see.

Need appliance repair help now?
Call now to be connected with a local appliance repair company in Denver.
(720) 679-7046

Hardness is the amount of dissolved calcium and magnesium in your tap water, and in the Denver metro it ranges from soft to very hard depending on which utility sends water to your house. That one number explains a lot of the scale, clogged lines and short-lived heating parts that repair companies see.

Why hardness matters to appliances

When water is heated or evaporates, dissolved minerals come out of solution and stick to whatever surface is there. Inside a dishwasher that surface is the heating element, the spray arms and the filter. In a washer it is the inlet valve screens and the heater on models that have one. In an ice maker it is the fill valve and the mold. Over time the film thickens, restricts flow and insulates metal from the water it is supposed to heat.

Denver Water says the water it delivers tends to form scale, and that scale typically starts to appear after about two to five years and keeps building over time. A Bosch dishwasher manual makes the same point from the appliance side: hard water leaves limescale on dishware and in the washing tank, parts of the machine may become blocked, and water above 9 degrees E needs to be softened to avoid damage. Those are two different sources saying the same thing, and neither depends on brand.

Hardness is not the same across the metro

The Denver area is served by dozens of separate water providers, and each one publishes its own numbers. The figures below are averages or ranges reported by the utilities themselves, in milligrams per liter (mg/L). They are a guide, not a measurement of your tap, because your house may sit on a different pressure zone or blend than the average.

  • Longmont: typically 1 to 2 grains per gallon, which the city calls soft.
  • Denver Water: about 105 mg/L on average, which the utility describes as soft to moderately hard.
  • Castle Rock Water: about 100 mg/L on average, called moderately hard.
  • Aurora Water: about 136 mg/L on average, with a reported range of 87 to 198.
  • Westminster: 112 to 149 mg/L, roughly 7 to 9 grains per gallon.
  • Highlands Ranch: usually 11 to 13 grains per gallon (188 to 222 mg/L), which the utility's scale calls hard.
  • Thornton: about 230 mg/L on average, and the city says its plants do not remove hardness.
  • South Adams County Water and Sanitation District: a current average of 21 grains per gallon (350 mg/L), with a softening project aimed at bringing it down.

Put side by side, a Thornton or South Adams kitchen gets water more than twice as hard as a Denver Water kitchen, and a Longmont kitchen gets water far softer than either. A dishwasher moved from one end of the metro to the other will not age the same way. If you rent a house in an unfamiliar suburb, check the utility name on the water bill before assuming anything about scale.

A few providers do not print a hardness value at all, and for those we do not state one. If your utility is silent, your own water bill, the utility's annual report or an inexpensive test strip from a hardware store will tell you more than a guess will.

What scale does, appliance by appliance

Dishwashers

White film on glasses and a gritty feel in the tub are the visible signs. Less visible is the heating element, which can be coated enough to run hotter and fail sooner, and the drain and spray components, which can narrow. A dishwasher that leaves water standing or washes poorly is often a scale and debris problem before it is a pump problem. Our guide on dishwasher drain and cleaning problems walks through what to check first.

Washers

Inlet screens at the back of a washer collect grit and mineral flakes, and a clogged screen means slow fills and error codes. Front-loaders add a door boot and drain pump where residue collects. Using more detergent than the label says does not help in hard water, and it adds to the film.

Refrigerators and ice makers

The water line to a fridge feeds a small valve that opens and closes thousands of times. Mineral particles can keep it from sealing, which shows up as slow ice, small cubes, hollow cubes or a leak at the valve. A water filter on the line helps with sediment, but a standard filter is not a softener and the cartridge needs changing on the schedule in your manual. Our page on ice maker repair in Denver covers the usual failures.

Water heaters, kettles and coffee makers

These are not repaired by an appliance company in most cases, but they are the first place many owners notice scale. A white crust on a kettle element is the same material forming inside your dishwasher where you cannot see it.

Maintenance that actually slows scale

  1. Run a dishwasher cleaning cycle with an approved descaler on the schedule your manual recommends, and clean the filter by hand more often than that.
  2. Pull and rinse the inlet screens on a washer when fills slow down. Turn the water off first and expect a little spillage.
  3. Use rinse aid in the dishwasher if the machine has a dispenser, since it helps water sheet off instead of drying into spots.
  4. Replace refrigerator water filters on the interval in the manual. An overdue cartridge restricts flow and strains the valve.
  5. Leave the washer door or lid open between loads so the drum dries, which slows residue and odor in the seals.

None of this removes hardness from the water. It only keeps the surfaces you can reach clear while the minerals keep arriving. For a whole house, a softener or other treatment is a plumbing decision, and the manuals for many appliances say that very hard water should be treated. Ask a plumber or water treatment company about that rather than a repair company, and check your appliance manual for its stated limit first.

Soft water is not a free pass

If you are in a soft-water area, scale is less of a concern, but other issues remain. Very soft water can cause excess suds, so detergent amounts should be cut to the low end of the label. Water that has been through a home softener also carries sodium, and some manufacturers note limits for it. Reading the water section of the manual is worth five minutes.

Symptoms that point to scale, and when to call

Call a local repair company when a fix needs parts opened up or replaced: a dishwasher that will not heat or drain after you have cleaned the filter, a washer that keeps throwing a fill error after the screens are clean, an ice maker that is not filling, or any appliance that is leaking. Rinsing a filter is homeowner work. Removing a heating element or replacing a valve usually is not, and water and power together call for caution.

Scale-related repairs are ordinary jobs, and national averages from HomeGuide put dishwasher repairs at about $100 to $300 and washer repairs at about $100 to $400. Those are national figures, not Denver quotes, and your own price depends on the part and the labor. When the machine is old, scale damage tends to be one of several wear points. Compare the quote with the repair or replace rule of thumb before deciding.

Getting a repair company on the phone

This site is a free referral service. It is not a repair company. A call connects you with an independent local appliance repair company, which sets its own prices and schedule. Mention the symptom, the make and model, and your town. Mentioning your water utility helps too, because a repair company that works your part of the metro already knows what hardness does to machines there.

Call now to be connected with a local appliance repair company in Denver.
(720) 679-7046

You can browse repair pages by appliance, such as dishwasher repair and washer repair, or look at the towns we cover, including Thornton and Highlands Ranch, where hardness is on the high side. The full list is on our service areas page, and more reading is in the guides index.

Frequently asked questions

How hard is Denver's tap water?
Denver Water reports about 105 mg/L on average and describes it as soft to moderately hard. Other utilities in the metro report different numbers, so your own provider's report is the better guide.
Which Denver-area utilities have the hardest water?
Among the utilities we have figures for, Thornton reports about 230 mg/L and South Adams County Water and Sanitation District reports a current average of 350 mg/L. Highlands Ranch usually reports 188 to 222 mg/L.
Does hard water void an appliance warranty?
It can depend on the wording. Some manuals set a hardness limit and say damage from water outside that limit is not covered, so read the water section of your manual and ask the manufacturer if you are unsure.
Can a repair company fix scale damage?
A local repair company can clear clogged lines, replace a coated heating element or swap a failing valve. Whether that is worth it depends on the age of the machine and the quote.
Call now to be connected with a local appliance repair company in Denver.
(720) 679-7046

Last updated:

☎ Call (720) 679-7046