Water left in the tub after a cycle, or dishes that come out cloudy and gritty, point to a short list of causes. Most of them involve the filter, the drain path or mineral buildup, and the first checks are simple.
A dishwasher drains through a pump, a hose and a connection to the sink drain or garbage disposal. When any piece of that path is blocked or weak, water stays behind. Cleaning trouble is often the same story from another angle: if the machine cannot move water properly, detergent and soil never leave. This guide goes from the easiest checks to the problems that need a repair visit.
Before you touch anything
Cut power before reaching into the machine. Switch the dishwasher breaker off, or unplug it if the cord is reachable under the sink. Many are hardwired, so the breaker is the usual route. Standing water in the tub is dirty and can contain broken glass or sharp bits, so wear gloves. Do not run the disposal while your hand is inside either unit.
If you smell gas in the kitchen, leave the house, call 911 from outside, and then call the gas utility. A dishwasher does not use gas, but a gas range or water heater nearby could be leaking, and sparks from a switch or a phone can ignite it.
Check the obvious first
Run the sink and the garbage disposal. If the sink drains slowly or the disposal is full of scraps, the dishwasher has nowhere to send water. Run the disposal with water running for half a minute to clear it. If the dishwasher drains into the disposal, a new installation may also still have the knockout plug in place. That small plastic disc inside the disposal inlet is a frequent cause for a dishwasher that never drained from the day it was installed.
Next, run the cycle again. Some models hold water briefly between phases, so confirm the water is still there at the end rather than in the middle of a cycle. Look at the control panel for error codes and check the manual for what they mean. A flashing drain code is useful information to give a repair company.
Clean the filter and sump
Most dishwashers have a filter at the bottom of the tub, often a cylinder you twist out, or a flat mesh beneath it. Food, label scraps, seeds and broken glass collect there. Take it out, rinse it under the tap and scrub it gently with a soft brush. Clean the sump area under it by hand, and remove anything that does not belong. A clogged filter is the most common reason for both slow draining and a gritty film, so do this monthly.
Check the spray arms as well. Mineral buildup and food block the small holes, and the arms then fail to wash the top rack. A toothpick clears them. Make sure the arms spin freely when you turn them by hand, and that a tall dish is not hitting them.
The drain hose and the air gap
The drain hose runs from the pump to the sink drain, and it can kink behind the machine or pinch where it passes through a cabinet. Pull the dishwasher forward only if you can do so safely with power off. A hose that dips low can also let wastewater flow back. A high loop, which is a bend that rises under the countertop before dropping to the drain, prevents this. Some kitchens have an air gap on the sink, a small cylinder next to the faucet. If it is clogged, water backs up into the tub. Pop off the cap and clear it.
A bad smell and murky water in the tub point to a blockage in the sink line instead. If the kitchen sink backs up too, the problem is the plumbing, not the dishwasher, and a plumber is the right call.
Why Denver-area dishes come out cloudy
Water hardness shapes how dishwashers wear. Denver Water says the water in its system tends to form scale, which typically begins to appear after about two to five years and keeps building. Its reported hardness is about 105 mg/L, soft to moderately hard, and some other providers around the metro deliver much harder water, so the picture depends on your address. You can read more in our water hardness guide.
A Bosch dishwasher manual says hard water leaves limescale on dishware and in the washing tank, and that parts of the appliance may become blocked. It adds that water above 9 degrees E should be softened to avoid damage. Scale narrows spray arm holes, coats the heating element and clogs the drain pump's small passages. White film on glasses and a rough feel inside the tub are the visible signs.
The fix is routine. Use the dishwasher's own descaler or run an empty hot cycle with a cleaner made for dishwashers, add rinse aid, and check whether the salt reservoir is full if your machine has one. Salt levels and the hardness setting inside the machine may need adjusting.
Detergent, loading and temperature
Poor cleaning that is not drainage often has a plain cause. Too little detergent, an expired pod, or too much pre-rinsing can leave film, because modern detergent needs soil to work against. Overloading blocks spray patterns, and a nested bowl will stay dirty no matter how new the machine is. Run the kitchen tap until the water is hot before starting a cycle so the dishwasher begins with hot water instead of cold from the pipe. If the heating element has failed, dishes dry poorly and greasy residue stays, which needs a repair.
Parts that fail
If the filter, hose, air gap and sink are clear, the cause is probably inside the machine. A repair company will usually look at:
- Drain pump. A jammed impeller or burned-out motor. A humming sound with no draining is typical.
- Drain check valve. A stuck flap lets dirty water drift back in.
- Circulation pump or motor. Weak pressure leaves soil on dishes even if water drains.
- Inlet valve. Too little water enters, so cleaning suffers.
- Heating element or thermostat. Water never gets hot enough.
- Control board or door latch switch. The cycle does not complete properly.
Our page on dishwasher repair in Denver covers these in more detail, and brand pages such as Bosch appliance repair in Denver explain typical weak points for popular lines. Brand names there only describe the products being repaired.
Leaks are a different problem
A dishwasher that leaks from the door, the base or under the sink needs attention fast, because water damages cabinets and flooring. Turn off the water supply valve under the sink, switch off the breaker, and call. Do not keep running cycles to see whether the leak repeats.
What to expect to pay
HomeGuide's national averages list dishwasher repair at $100 to $300. Its general range for appliance repair is $100 to $400, and a service call runs $70 to $130 nationally. These are national figures and not Denver prices. Where the filter and hose are the whole story, the bill can be small. A pump or board will cost more. Ask for a price before the work begins and for the call-out charge to be explained.
Repair or replace
NAHB lists 10 years as typical dishwasher life, which is shorter than most kitchen appliances. A machine at seven or eight years with a failed pump is a closer call than a three-year-old one. The 50% rule from Angi suggests replacing when the repair would be half or more of the cost of a new model, including installation. Built-in dishwashers also need a fitted space, so a replacement is not always a simple swap. See the repair or replace guide for the full reasoning.
When to call
If the filter is clean, the sink drains well and the hose is clear but water still stands in the tub, it is time for a repair company. The same goes for a pump that hums, a machine that trips the breaker, or a cycle that stops partway. Companies serve towns across the metro, for example Thornton dishwasher repair and Arvada dishwasher repair, and Thornton's water is reported as much harder than Denver's, which matters for scale.
This site is a free referral service. The number connects you with an independent local appliance repair company, and that company sets its own pricing. See the whole guides library for more troubleshooting help, or the services list for other appliances we cover.
Frequently asked questions
Why is there standing water in my dishwasher after a cycle?
Why do my dishes come out cloudy in the Denver area?
How often should I clean the dishwasher filter?
How much does dishwasher repair cost?
Sources
Last updated: